← Blog

Do I Need an Oversize Permit? Width, Height, Length and Weight Checks

Published ·Updated ·12 min read ·11 sections

Published by JaloPermit. Federal limits come from the regulation (23 CFR 658.13, 23 CFR 658.15, 23 CFR 658.16, 23 CFR 658.17) and FHWA’s own guides; state heights and widths come from each state’s statute, rule or DOT page, linked in the table. All checked November 16, 2026. This is a plain-English checklist, not legal advice. The issuing state’s rules and the permit itself govern your move: the permit face wins.

Use this checklist to decide whether you need an oversize permit or an oversize load permit for size, or an overweight permit for weight. Limits below came from official federal and state sources, checked November 16, 2026. JaloPermit is a reading aid, not a permit-filing service.

You need an oversize/overweight permit if your loaded truck is wider than 8 ft 6 in (102 in), taller than the state’s height limit (13 ft 6 in to 14 ft 6 in in the states we checked), longer than the state’s length limits, or heavier than 80,000 lb gross, 20,000 lb on a single axle or 34,000 lb on a tandem. Fail any one check and you need a permit from each state on the route before you move.

The quick check is below, then each measurement in a bit more detail, a table of legal heights and widths for 17 states we checked on their own official sources today, and the two follow-up questions that decide what kind of permit you can get: is the load nondivisible, and is it a single trip or an annual move?

This page is the yes/no checklist. If you already hold a permit and want to read it, start with how to read an oversize load permit.

The 60-second checklist

Measure the truck with the load on it, then run these five checks. If you are over on any line, you need a permit.

CheckUsual legal limitWho sets itYou likely need a permit if
Width8 ft 6 in (102 in), load includedFederal rule for the National Network (23 CFR 658.15); states set it on other roadsAny part of the truck or load is wider than 102 in, not counting excluded devices such as mirrors
Height13 ft 6 in to 14 ft 6 in in the 17 states belowEach state; there is no federal height limit (FHWA’s Federal Size Regulations for Commercial Motor Vehicles)The loaded height from the road surface is over your state’s number
LengthVaries: states must allow at least a 48 ft semitrailer in a tractor-semitrailer (23 CFR 658.13(b)(1))States, within federal minimumsYour trailer, overall length or load overhang is over the state’s limit
Gross weight80,000 lb on the Interstate SystemFederal (23 CFR 658.17(b)); states on other roadsThe whole loaded truck weighs more than 80,000 lb, or more than the bridge formula allows
Axle weight20,000 lb single axle; 34,000 lb tandemFederal (23 CFR 658.17(c), 23 CFR 658.17(d))Any axle or axle group is over, even if the gross is legal

Federal numbers apply on the Interstate System and the National Network of truck routes. On other roads, the state sets the limit, and it can be different. If your state differs, its JaloPermit Atlas page has the basics, and our oversize permit guides by state link every state’s permit office.

Width: 8 ft 6 in (102 in)

Federal law says no state may set a width limit “of more or less than 102 inches” on a vehicle on the National Network (23 CFR 658.15(a)). The same section lets states grant special permits for vehicles wider than 102 inches (23 CFR 658.15(c)). That permit is your oversize permit.

What counts toward width: everything not excluded by law. 23 CFR 658.16 excludes rear-view mirrors, turn signal lamps, handholds, splash and spray suppressant devices and load-induced tire bulge, plus non-property-carrying devices that stick out no more than 3 inches on each side. Your load is never excluded. A 102-inch trailer carrying a 10-foot-wide machine is 10 feet wide.

Most of the 17 states we checked use 8 ft 6 in or 102 in on all of their highways. Michigan’s statute is the exception: its base rule is 96 inches for the body or load, with 102 inches allowed on highways the state or a local agency designates (MCL 257.717(1), (7)). Federal law still requires 102 inches on the National Network.

Height: set by each state

There is no federal height limit. FHWA’s Federal Size Regulations for Commercial Motor Vehicles says states set their own and that “most height limits range from 13 feet, 6 inches … to 14 feet.”

In the states we checked today, legal height runs from 13 ft 6 in (Florida, Illinois, Iowa, Michigan, Minnesota, Ohio, Virginia) to 14 ft (California, Kansas, North Dakota, Texas, Washington, Wyoming) to 14 ft 6 in (Colorado and Nebraska). Missouri and Louisiana allow 14 ft on Interstates and 13 ft 6 in on other highways. Flag: Colorado and Nebraska are higher than the range FHWA calls typical, so don’t assume 14 ft is the ceiling everywhere.

Legal height is not the same as clearance. Bridges and wires can be lower than the legal limit, and some statutes say so directly: California allows 14 ft but says anything over 13 ft 6 in may run only where the owner deems it safe (Veh. Code § 35250). Our guide to bridge clearance maps for trucks lists free official sources for low bridges.

Length: trailer, overall and overhang

Federal length rules are mostly minimums that states must allow on the National Network (23 CFR 658.13):

  • States must allow a semitrailer of at least 48 ft in a tractor-semitrailer combination, and may not set an overall length limit on that combination.
  • States must allow trailers of at least 28 ft in a tractor-semitrailer-trailer (doubles) combination.

Above those minimums, each state writes its own caps, and they vary. For example: Kansas allows a semitrailer up to 59 ft 6 in (K.S.A. 8-1904(d)); Colorado says there is no overall limit for a tractor-semitrailer as long as the trailer is no more than 57 ft 4 in (CDOT FAQ); Michigan caps the semitrailer at 50 ft (MCL 257.719); Minnesota’s statewide rule is 48 ft, or up to 53 ft with a kingpin-to-rear-axle distance of 43 ft or less (Minn. Stat. § 169.81).

Load overhang matters too. A load sticking out past the front or rear can push you over a state’s length or overhang limit even on a legal-length trailer, so check the state’s rule for your route.

Weight: 80,000 lb, axles and the bridge formula

On the Interstate System and reasonable access to it, the federal limits are (23 CFR 658.17):

  • 80,000 lb gross, unless the bridge formula sets a lower number.
  • 20,000 lb on any one axle.
  • 34,000 lb on a tandem axle.
  • The Bridge Gross Weight Formula for any two or more consecutive axles, which ties allowed weight to the number of axles and the distance between them (23 CFR 658.17(e)).

Being under 80,000 lb gross does not settle it. FHWA’s Bridge Formula Weights guide says any group of consecutive axles must meet the formula even when single, tandem and gross weights are legal. For how those numbers show up on a permit, see overweight permit axle weights.

Flag: limits can be higher in places. FHWA notes that some states kept higher “grandfathered” Interstate limits (FHWA’s Bridge Formula Weights guide), and states set their own limits off the Interstate. Colorado, for example, lists 85,000 lb on non-Interstate highways (CDOT FAQ). Use the state’s own number for the roads you’ll run.

Legal height and width in 17 states (checked Nov 16, 2026)

Each row below was read today on the state’s own statute, rule or DOT page. We left out every state we could not confirm today from an official source, including Pennsylvania, Utah and New Mexico. For those, see the state’s JaloPermit Atlas page or our state guides hub.

StateLegal widthLegal heightOfficial sourceChecked
California
State guide · Atlas
102 in14 ft (statute says over 13 ft 6 in only on highways the owner deems safe)Veh. Code § 35100; § 35250Nov 16, 2026
Colorado
State guide · Atlas
8 ft 6 in14 ft 6 inCDOT permitting information FAQNov 16, 2026
Florida
State guide · Atlas
102 in13 ft 6 in (14 ft for automobile transporters)Fla. Stat. § 316.515(1)–(2)Nov 16, 2026
Illinois
State guide · Atlas
8 ft 6 in13 ft 6 in625 ILCS 5/15-102; 5/15-103Nov 16, 2026
Iowa
State guide · Atlas
8 ft 6 in13 ft 6 inIowa Code § 321.454 (PDF); § 321.456 (PDF)Nov 16, 2026
Kansas
State guide · Atlas
8 ft 6 in14 ftK.S.A. 8-1902; 8-1904Nov 16, 2026
Louisiana
State guide · Atlas
102 in14 ft on Interstates; 13 ft 6 in on other highwaysDOTD Rules and Regulations book, 2026 (PDF)Nov 16, 2026
Michigan
State guide · Atlas
96 in body/load in the base rule; 102 in on highways designated for it (see note)13 ft 6 inMCL 257.717; 257.719Nov 16, 2026
Minnesota
State guide · Atlas
102 in13 ft 6 inMinn. Stat. § 169.80; § 169.81Nov 16, 2026
Missouri
State guide · Atlas
102 in14 ft on Interstates and designated routes; 13 ft 6 in on other highwaysRSMo 304.170Nov 16, 2026
Nebraska
State guide · Atlas
102 in14 ft 6 inNeb. Rev. Stat. § 60-6,288; § 60-6,289Nov 16, 2026
North Dakota
State guide · Atlas
8 ft 6 in14 ftN.D.C.C. § 39-12-04 (PDF)Nov 16, 2026
Ohio
State guide · Atlas
102 in13 ft 6 inOhio Rev. Code § 5577.05Nov 16, 2026
Texas
State guide · Atlas
102 in14 ftTransp. Code §§ 621.201, 621.207Nov 16, 2026
Virginia
State guide · Atlas
102 in13 ft 6 inVa. Code § 46.2-1105; § 46.2-1110Nov 16, 2026
Washington
Atlas page
8 ft 6 in14 ftRCW 46.44.010; 46.44.020Nov 16, 2026
Wyoming
State guide · Atlas
8 ft 6 in (102 in)14 ftWYDOT rules ch. 5, § 3Nov 16, 2026

Notes and disagreements:

  • Colorado comes from CDOT’s permitting FAQ (“Colorado’s legal height limit is 14 foot 6 inches”). We did not read the Colorado statute itself today.
  • Michigan’s statute sets 96 inches as the base body/load width, with 102 inches on designated highways; federal rules require 102 inches on the National Network. Ask the Michigan permit office if your route leaves designated highways.
  • Illinois sets 8 ft 6 in on Class III and non-designated highways in § 15-102(a), and allows the same 8 ft 6 in, excluding certain safety devices, on Interstates and Class I and II highways in § 15-102(e).
  • Florida was read on the Florida Senate’s 2025 statutes page, the current published edition.
  • Heights for Missouri and Louisiana depend on the road type, as shown.

Is your load nondivisible?

Being over a limit is half the question. The other half is whether the state will permit your load at all.

Federal rules let states issue special permits above the axle, gross and bridge-formula limits for nondivisible vehicles or loads (23 CFR 658.17(h)). 23 CFR 658.5 defines nondivisible as a load that, if split, would lose its use or value, or would take more than 8 work-hours to take apart. A single bulldozer is nondivisible. A trailer of pipe or a tank of water is not: take some off and you’re legal.

Some states apply the same test to oversize permits too. Wyoming’s rules, for example, say oversize and overweight permits are issued only for loads meeting non-divisible requirements (WYDOT rules ch. 5). Some states also sell special permits for certain divisible loads off the Interstate, such as Colorado’s non-Interstate overweight divisible permits (CDOT permitting information). For the full rule, see what is a nondivisible load.

Single-trip or annual?

Many states, including Colorado, Wyoming and Louisiana, offer both of these:

  • Single-trip: one move, on a set route, in a set time window. This is what most one-off oversize loads get.
  • Annual (or blanket): repeat moves for a year under size and weight caps the state sets. Colorado’s annual non-divisible load permits, for example, top out at 16 ft high, 17 ft wide and 200,000 lb gross, with length caps by road type (CDOT permitting information).

If your load is over a state’s annual caps, ask its permit office which permit type applies. Bigger loads also bring pilot cars; see how many pilot cars your load needs and pilot car requirements by state. Our OS/OW permit terms glossary explains single-trip, annual and superload, and what is a superload shows where each state draws that line.

Once you have the permit, the permit face wins

The limits on this page tell you whether you need a permit. Once the state issues one, the permit tells you how to move: the route, the dimensions and weights you’re allowed, travel hours, pilot cars and any special conditions. If the permit and a general rule seem to disagree, follow the permit and call the issuing office about anything unclear.

Our guide on how to read an oversize load permit walks through each part. To see every limit on one card, drop the issued permit PDF into the JaloPermit decoder: it lays out the route, pilot cars, curfews, dimensions and limits so you can check them against the original.

JaloPermit, which publishes this guide, is a reading aid for issued permit PDFs. It is not a permit-filing service and it does not plan routes or provide navigation. The issued permit always wins.

Questions about how JaloPermit reads a permit? Email support@jalopermit.org.

Oversize load permit or overweight permit?

An oversize load permit (often searched simply as an oversize permit) is for width, height or length over the legal limits. An overweight permit is for gross or axle weight over the legal limits, commonly 80,000 pounds gross on the interstate system, plus axle and bridge-formula limits. Many states issue both as one permit.

Once the state issues the document, read it with How to Read an Oversize Load Permit and, if weight is involved, Overweight Permit Axle Weights: How to Read Them. Field-by-field state guides are at How to Read an Oversize Permit: All 48 State Guides.

FAQs

Do I need an oversize permit for a load 8 feet 6 inches wide? Not for width alone. 8 ft 6 in (102 in) is the federal width limit on the National Network (23 CFR 658.15), and every state in our table allows it on at least its main truck routes. Over 102 in, you need a permit. Michigan is the one state we checked whose base statute uses 96 in for the load off designated highways.

Is there a federal height limit for trucks? No. FHWA’s Federal Size Regulations for Commercial Motor Vehicles says there is no federal height requirement, so each state sets its own. The states we checked use 13 ft 6 in, 14 ft or 14 ft 6 in, and Missouri and Louisiana use different numbers on different road types.

Do I need a permit if I’m only overweight? Yes, if you’re over gross, axle or bridge-formula limits. On the Interstate System, federal rules let states issue those permits only for nondivisible loads (23 CFR 658.17(h)). If the load can be split, the expected answer is to split it. See what is a nondivisible load.

Do I need a separate permit for each state? Yes. Each state issues its own permit for its own roads, and some local road authorities issue their own too. A multi-state move means one permit per state. See multi-state oversize permit trips.

Single-trip or annual permit: which do I need? A single-trip permit covers one move on a set route and time window. Annual permits cover repeat moves under size and weight caps the state sets. Which ones you can get depends on the state and on how big the load is.

Does JaloPermit get the permit for me? No. JaloPermit is a reading aid, not a permit-filing service. Once a state issues your permit, upload the PDF and it decodes the route, pilot cars, curfews and dimensions onto one card. Guests get three free decodes a day with no account and no card. Logged-in users get 10 free decodes a day. After those free decodes, each one is $3.50. There is no subscription.

What is the difference between an oversize load permit and an overweight permit? An oversize load permit covers legal width, height or length. An overweight permit covers legal gross or axle weight. You may need one, the other, or both. The issuing state’s permit is the authority.